Characterizing Flocculated Mineral Sediments with Acoustic Backscatter, Using Solid and Hybrid Scattering Models.

This study investigated the performance of an acoustic backscatter system (ABS) for the in situ particle characterization of complex wastes. Two sediments were used: a fine, milled calcite that was flocculated with anionic polyacrylamide and naturally flocculated pond sludge. Particles were initially measured independently by light-based techniques to gain size, the coefficient of variation (COV), and fractal dimensions. For acoustic experiments, a bespoke, high-fidelity ABS was employed with 1, 2.25, and 5 MHz probes and a recirculating mixing tank. Initially, the concentration independent attenuation and backscatter coefficients were measured for each system using a robust calibration procedure at multiple concentrations. Comparisons of the total scattering cross-section (χ) and form function (f) were made between the experimental data and two semiempirical models: a Solid Scattering model and a Hybrid model (where the effects of bound fluid are incorporated). Experimental data compared more closely to the Solid Scattering model, as it was assumed scattering was dominated by small, bound "flocculi" rather than the macroscopic structure. However, if the COV was used as a fit parameter, the hybrid model could give equally accurate fits for a range of input aggregate sizes, highlighting that important size and structure information can be gained from the acoustic models if there is some a priori system data. Additionally, dual-frequency inversions were undertaken to measure concentration profiles for various frequency pairs. Here, the lowest frequency pair gave the best performance (with accurate measurements in the range of 2-35 g·L-1) as interparticle scattering was lowest.

Analysis of Adsorbed Polyphosphate Changes on Milled Titanium Dioxide, Using Low-Field Relaxation NMR and Photoelectron Spectroscopy.

In this study, changes in the adsorbed amount and surface structure of sodium hexametaphosphate (SHMP) were investigated for aluminum-doped TiO2 pigment undergoing milling. Relaxation NMR was utilized as a potential at-line technique to monitor the effect of milling on surface area and surface chemistry, while XPS was used primarily to consider the dispersant structure. Results showed that considerable amounts of weakly adsorbed SHMP could be removed with washing, and the level of dispersant removal increased with time, highlighting destructive effects of sustained high-energy milling. Nonetheless, there were no significant chemical changes to the dispersant, although increases to the bridging oxygen (BO) peak full width at half-maximum (FWHM) suggested some chemical degradation was occurring with excess milling. Relaxation NMR revealed a number of important features. Results with unmilled material indicated that dispersant adsorption could be tracked with pseudo-isotherms using the relative enhancement rate (Rsp), where the Rsp decreased with dispersant coverage, owing to partial blocking of the quadrupolar surface aluminum. Milled samples were also tracked, with very accurate calibrations of surface area possible from either T1 or T2 relaxation data for systems without dispersant. Behavior was considerably more complicated with SHMP, as there appeared to be an interplay between the dispersant surface coverage and relaxation enhancement from the surface aluminum. Nevertheless, findings highlight that relaxation NMR could be used as a real-time technique to monitor the extent of milling processes, so long as appropriate industrial calibrations can be achieved.

Capillary module haemodynamics and mechanisms of blood flow regulation in skeletal muscle capillary networks: Experimental and computational analysis.

The capillary module (CM), consisting of parallel capillaries from terminal arteriole to post-capillary venule, is classically considered to be the building block of complex capillary networks. In skeletal muscle, CMs form interconnected columns spanning thousands of microns, which we recently described as the capillary fascicle. However, detailed evaluation of CM haemodynamics has not been described, and may provide insight into mechanisms of blood flow regulation in the microcirculation. We used intravital videomicroscopy from resting extensor digitorum longus muscle in rats (n = 9 networks, 112 capillary modules), as well as dual-phase computational modelling of blood flow in simulated CM geometries. We found that the mean driving pressure across CMs was 3.236 ± 1.833 mmHg. Red blood cell (RBC) flow was independent of CM resistance, and the ratio of blood flow in adjacent modules was not correlated with their ratio of resistances. In simulated CM geometries, increases to driving pressure produced a direct linear increase to RBC and plasma flow, with no changes to RBC distribution; increases to arteriolar inflow haematocrit resulted in increased RBC flow, but with viscosity-dependent increases to CM resistance. CM RBC flow heterogeneity was higher than plasma flow heterogeneity in experimental data, in contrast to simulated geometries, suggesting that time-dependent flow variability may have important consequences for RBC distribution. In summary, these findings suggest that CMs are active participants in microvascular flow regulation, likely achieved through adjustments to CM driving pressure using pre- and post-capillary loci of flow control. Increases to CM viscosity may be important during the regulation of functional hyperaemia. KEY POINTS: The capillary module (CM), consisting of parallel capillaries from the arteriole to venule, is classically considered to be the building block of capillary networks in skeletal muscle. A detailed evaluation of module haemodynamics may provide insight into mechanisms of blood flow regulation in the microcirculation. Using experimental data from resting skeletal muscle in rats, as well as dual-phase computational models of blood flow, we analysed haemodynamic relationships and the impact of variations to boundary conditions on red blood cell and plasma distribution. We showed that driving pressure across CMs is low, and that simulated increases to inflow haematocrit have important viscosity-dependent effects on module resistance. We found that red blood cell flow was independent from module resistance, which strongly suggests the regulation of driving pressure at the level of the capillary module using pre- and post-capillary loci of flow control. These findings place CMs as central participants in microvascular flow regulation, with important consequences for disease and functional hyperaemia.

The capillary fascicle in skeletal muscle: Structural and functional physiology of RBC distribution in capillary networks.

KEY POINTS: The capillary module, consisting of parallel capillaries from arteriole to venule, is classically considered as the building block of complex capillary networks. In skeletal muscle, this structure fails to address how blood flow is regulated along the entire length of the synchronously contracting muscle fibres. Using intravital video microscopy of resting extensor digitorum longus muscle in rats, we demonstrated the capillary fascicle as a series of interconnected modules forming continuous columns that align naturally with the dimensions of the muscle fascicle. We observed structural heterogeneity for module topology, and functional heterogeneity in space and time for capillary-red blood cell (RBC) haemodynamics within a module and between modules. We found that module RBC haemodynamics were independent of module resistance, providing direct evidence for microvascular flow regulation at the level of the capillary module. The capillary fascicle is an updated paradigm for characterizing blood flow and RBC distribution in skeletal muscle capillary networks. ABSTRACT: Capillary networks are the fundamental site of oxygen exchange in the microcirculation. The capillary module (CM), consisting of parallel capillaries from terminal arteriole (TA) to post-capillary venule (PCV), is classically considered as the building block of complex capillary networks. In skeletal muscle, this structure fails to address how blood flow is regulated along the entire length of the synchronously contracting muscle fibres, requiring co-ordination from numerous modules. It has previously been recognized that TAs and PCVs interact with multiple CMs, creating interconnected networks. Using label-free intravital video microscopy of resting extensor digitorum longus muscle in rats, we found that these networks form continuous columns of linked CMs spanning thousands of microns, herein denoted as the capillary fascicle (CF); this structure aligns naturally with the dimensions of the muscle fascicle. We measured capillary-red blood cell (RBC) haemodynamics and module topology (n = 9 networks, 327 modules, 1491 capillary segments). The average module had length 481 µm, width 157 µm and 9.51 parallel capillaries. We observed structural heterogeneity for CM topology, and functional heterogeneity in space and time for capillary-RBC haemodynamics within a module and between modules. There was no correlation between capillary RBC velocity and lineal density. A passive inverse relationship between module length and haemodynamics was remarkably absent, providing direct evidence for microvascular flow regulation at the level of the CM. In summary, the CF is an updated paradigm for characterizing RBC distribution in skeletal muscle, and strengthens the theory of capillary networks as major contributors to the signal that regulates capillary perfusion.

Flotation using sodium dodecyl sulphate and sodium lauroyl isethionate for rapid dewatering of Mg(OH)2 radwaste suspensions.

Mg(OH)2 suspensions were floated utilising sodium dodecyl sulphate (SDS) and sodium lauroyl isethionate (SLI) collectors, for rapid dewatering of radwaste suspensions. Freundlich adsorption isotherms were first used to compare the adsorption densities of SDS and SLI on Mg(OH)2 surfaces, to determine the maximum monolayer coverage capacity, and were found to be 0.11 µmol m-2 at a dosed concentration of 172 µM for SDS and 0.05 µmol m-2 at a dosed concentration of 188 µM for SLI. The natural and salt induced coagulation kinetics of Mg(OH)2 were examined using static light scattering, where the influence of collector adsorption on particle size distributions was also investigated, to probe potential hydrodynamic limitations of flotation. Particle stabilised foam formation was then characterised using a Bikerman column test, where the dynamic foamability indices (DFIs) of SDS and SLI were determined to be 49 × 103 s L mol-1 and 321 × 103 s L mol-1 respectively. Flotation performance was measured, and a collection efficiency factor used to compare the solid-liquid separation ability of mixed 2.5 vol% suspensions with SDS or SLI, as well as MIBC frother. Optimal performance aligned with collector concentrations relating to predicted maximum monolayer coverage, and whilst both surfactants were effective, SDS systems performed better than SLI in all metrics. Recoveries of >80% of the Mg(OH)2 wastes were achieved, whilst only transferring 35% of the water mass at the optimum SDS dosed concentration of 82 µM, likely due to its denser surface adsorption and minimised lamella water entrainment.

The effect of cationic surfactants on improving natural clinoptilolite for the flotation of cesium.

Flotation using cationic surfactants has been investigated as a rapid separation technique to dewater clinoptilolite ion exchange resins, for the decontamination of radioactive cesium ions (Cs+) from nuclear waste effluent. Initial kinetic and equilibrium adsorption studies of cesium, suggested the large surface area to volume ratio of the fine zeolite contributed to fast adsorption kinetics and high capacities (qc = 158.3 mg/g). Adsorption of ethylhexadecyldimethylammonium bromide (EHDa-Br) and cetylpyridinium chloride (CPC) surfactant collectors onto both clean and 5 ppm Cs+ contaminated clinoptilolite was then measured, where distribution coefficients (Kd) as high as 10,000 mL/g were evident with moderate concentrations CPC. Measurements of particle sizes confirmed that adsorption of surfactant monolayers did not lead to significant aggregation of the clinoptilolite, while < 8% of the 5 ppm contaminated cesium was remobilised. Importantly for flotation, both the recovery efficiency and dewatering ratios were measured across various surfactant concentrations. Optimum conditions were found with 0.5 mM of CPC and addition of 30 µL of MIBC frother, giving a recovery of ∼90% and a water reduction ratio > 4, highlighting the great viability of flotation to separate and concentrate the contaminated powder in the froth phase.

Acid number, viscosity and end-point detection in a multiphase high temperature polymerisation process using an online miniaturised MEMS Fabry-Pérot interferometer.

Recent advances in the latest generation of MEMS (micro-electro-mechanical system) Fabry-Pérot interferometers (FPI) for near infrared (NIR) wavelengths has led to the development of ultra-fast and low cost NIR sensors with potential to be used by the process industry. One of these miniaturised sensors operating from 1350 to 1650 nm, was integrated into a software platform to monitor a multiphase solid-gas-liquid process, for the production of saturated polyester resins. Twelve batches were run in a 2 L reactor mimicking industrial conditions (24 h process, with temperatures ranging from 220 to 240 °C), using an immersion NIR transmission probe. Because of the multiphase nature of the reaction, strong interference produced by process disturbances such as temperature variations and the presence of solid particles and bubbles in the online spectra required robust pre-processing algorithms and a good long-term stability of the probe. These allowed partial least squares (PLS) regression models to be built for the key analytical parameters acid number and viscosity. In parallel, spectra were also used to build an end-point detection model based on principal component analysis (PCA) for multivariate statistical process control (MSPC). The novel MEMS-FPI sensor combined with robust chemometric analysis proved to be a suitable and affordable alternative for online process monitoring, contributing to sustainability in the process industry.

Bio-Inspired Preparation of Clay-Hexacyanoferrate Composite Hydrogels as Super Adsorbents for Cs.

A facile and low-cost fabrication route, inspired by the adhesive proteins secreted by mussels, has been developed to prepare a clay-based composite hydrogel (DHG(Cu)) containing hexacyanoferrate (HCF) nanoparticles for the selective removal of Cs+ from contaminated water. Initially, montmorillonite was exfoliated prior to coating with a thin layer of polydopamine (PDOPA) via the self-polymerization of dopamine. Mixing the composite (D-clay) with the HCF precursor, followed by the addition of copper ions, led to the self-assembly of the polymer-coated exfoliated clay nanosheets into a three-dimensional network and in situ growth of KCuHCF nanoparticles embedded within the gel structure. Analytical characterization verified the fabrication route and KCuHCF immobilization by a copper-ligand complexation. Rheology testing revealed the composite hydrogel to be elastic under low strain and exhibited reversible, self-healing behavior following high strain deformation, providing a good retention of KCuHCF nanoparticles in the membrane. The adsorbent DHG(Cu) showed a superior Cs+ adsorption capacity (∼173 mg/g), with the performance maintained over a wide pH range, and an excellent selectivity for Cs+ when dispersed in seawater at low concentrations of 0.2 ppm. On the basis of its excellent mechanico-chemical properties, the fabricated hydrogel was tested as a membrane in column filtration, showing excellent removal of Cs+ from Milli-Q water and seawater, with the performance only limited by the fluid residence time. For comparison, the study also considered other composite hydrogels, which were fabricated as intermediates of DHG(Cu) or fabricated with Fe3+ as the cross-linker and reactant for HCF nanoparticle synthesis.

Process Monitoring of Moisture Content and Mass Transfer Rate in a Fluidised Bed with a Low Cost Inline MEMS NIR Sensor.

PURPOSE: The current trend for continuous drug product manufacturing requires new, affordable process analytical techniques (PAT) to ensure control of processing. This work evaluates whether property models based on spectral data from recent Fabry-Pérot Interferometer based NIR sensors can generate a high-resolution moisture signal suitable for process control. METHODS: Spectral data and offline moisture content were recorded for 14 fluid bed dryer batches of pharmaceutical granules. A PLS moisture model was constructed resulting in a high resolution moisture signal, used to demonstrate (i) endpoint determination and (ii) evaluation of mass transfer performance. RESULTS: The sensors appear robust with respect to vibration and ambient temperature changes, and the accuracy of water content predictions (±13 % ) is similar to those reported for high specification NIR sensors. Fusion of temperature and moisture content signal allowed monitoring of water transport rates in the fluidised bed and highlighted the importance water transport within the solid phase at low moisture levels. The NIR data was also successfully used with PCA-based MSPC models for endpoint detection. CONCLUSIONS: The spectral quality of the small form factor NIR sensor and its robustness is clearly sufficient for the construction and application of PLS models as well as PCA-based MSPC moisture models. The resulting high resolution moisture content signal was successfully used for endpoint detection and monitoring the mass transfer rate.

An ultra-compact particle size analyser using a CMOS image sensor and machine learning.

Light scattering is a fundamental property that can be exploited to create essential devices such as particle analysers. The most common particle size analyser relies on measuring the angle-dependent diffracted light from a sample illuminated by a laser beam. Compared to other non-light-based counterparts, such a laser diffraction scheme offers precision, but it does so at the expense of size, complexity and cost. In this paper, we introduce the concept of a new particle size analyser in a collimated beam configuration using a consumer electronic camera and machine learning. The key novelty is a small form factor angular spatial filter that allows for the collection of light scattered by the particles up to predefined discrete angles. The filter is combined with a light-emitting diode and a complementary metal-oxide-semiconductor image sensor array to acquire angularly resolved scattering images. From these images, a machine learning model predicts the volume median diameter of the particles. To validate the proposed device, glass beads with diameters ranging from 13 to 125 µm were measured in suspension at several concentrations. We were able to correct for multiple scattering effects and predict the particle size with mean absolute percentage errors of 5.09% and 2.5% for the cases without and with concentration as an input parameter, respectively. When only spherical particles were analysed, the former error was significantly reduced (0.72%). Given that it is compact (on the order of ten cm) and built with low-cost consumer electronics, the newly designed particle size analyser has significant potential for use outside a standard laboratory, for example, in online and in-line industrial process monitoring.

Sediment Microstructure and the Establishment of Gas Migration Pathways during Bubble Growth.

Soft sediments exhibit complex and varied deformation behavior during in situ bubble growth; however, the sediment microstructure is often neglected when predicting bubble networking or fracture propagation dynamics. This study considers three chemically similar Mg(OH)2-rich sediments, which differ slightly in their particle size distributions and morphologies but exhibit significant differences in their porosity, stiffness, and pore throat dimensions at equivalent yield strengths. At low yield strengths, microstructure greatly influenced the size distribution and connectivity of spherical bubble populations, with narrow sedimentary pore throats promoting coarser bubbles with diminished connectivity. Increased connectivity of the bubble population appeared highly significant in limiting bed expansion, either by establishing pathways for gas release or by dissipating excess internal bubble pressure, thereby diminishing further growth. During in situ gas generation, each sediment demonstrated a critical fracture strength, which demarcated the populations with high void fractions (0.27 < ν < 0.4) of near-spherical bubbles from a fracturing regime supporting reduced void fractions (ν ≈ 0.15) of high aspect ratio cracks. However, critical fracture strengths varied significantly (in the 60-1000 Pa range) between sediments, with coarser-grained and higher porosity sediments promoting fracture at lower strengths. Fracture propagation greatly enhanced the connectivity and diminished the tortuosity of the void networks, thereby augmenting the continuous gas release flux.

Not Just Hocus POCUS: Implementation of a Point of Care Ultrasound Curriculum for Internal Medicine Trainees at a Large Residency Program.

INTRODUCTION: In 2018, the American College of Physicians formally acknowledged the importance of Point of Care Ultrasound (POCUS) to the practice of internal medicine (IM). For the military internist, POCUS training is critical for care of the trauma patient in austere environments, mass casualty events and natural disasters. While emergency medicine and critical care training programs have adopted POCUS education, few IM programs have integrated POCUS into their core curricula. We designed and implemented an iterative POCUS curriculum for trainees at a large military IM residency program over a two-year period. METHODS: In collaboration with our critical care and simulation departments, we developed a pilot curriculum consisting of five, 60-minute courses offered on a voluntary basis at monthly intervals throughout 2017. Based on the pilot's success we incorporated a POCUS curriculum into the core academics received by all IM trainees during the 2017-2018 academic year. Trainees attended seven, 3-hour sessions during their scheduled academic time taught by subspecialists with POCUS expertise in an on-site simulation center. Baseline surveys and knowledge assessment examinations were administered during orientation and repeated at the end of the academic year. Comparison of results before and after the POCUS curriculum was the primary outcome evaluated. RESULTS: Intervention #1: Pilot, 2016-2017 Academic Year45 trainees attended at least one course with an average of 1.8 sessions per trainee. Baseline survey data showed 91% of trainees believe POCUS is quite or extremely beneficial for their patients, but 73% feel slightly or not at all confident in POCUS knowledge. The pre-test mean and median scores were 71% and 77% respectively, which both increased to a post-test mean and median of 81%. Post-test mean percentage correct for trainees attending 1, 2, or 3 courses was 74%, 82%, and 91% respectively. Intervention #2: Incorporation of POCUS into Core Academics, 2017-2018 Academic YearAll 75 trainees participated in training with an average of 3.77 sessions attended per trainee. Survey analysis revealed significant improvement in confidence of performing ultrasound-guided procedures (p = 0.0139), and a 37% absolute increase in respondents who anticipate using ultrasound in their clinical practice (p = 0.0003). The mean pre-test score was 67.8% with median of 63.6% while mean and median post-test scores were 82.1% and 81.8%, with an absolute improvement of 14.3% and 18.2% respectively (p = 0.0004). CONCLUSION: A structured POCUS curriculum was successfully incorporated at a large multiservice military IM residency program, with demonstrated retention of knowledge, improved confidence in performance of ultrasound guided invasive procedures, and increased interest in the use of POCUS in future clinical practice. Similar programs should be implemented across all IM programs in military graduate medical education to enhance operational readiness and battlefield care.

Characterisation of polyphosphate coated aluminium-doped titania nanoparticles during milling.

This paper investigates the characterisation of alumina-doped titania nanoparticles, milled under high-shear over time, in the presence of sodium hexametaphosphate (SHMP) dispersant. Transmission electron microscopy (TEM) indicated that prolonged milling times led to the formation of 10 nm particle fines which were electrostatically attracted to larger particles, where no change in the crystal structure was observed. Primary particle sizes measured by dynamic light scattering (DLS) and TEM were in agreement and showed no change in primary particle size (∼250 nm) with respect to milling time, however, there was a clear reduction in the magnitude of the slow mode decay associated to aggregates. The TiO2 was found to have an isoelectric point (iep) in the range of pH 3-4.5, where an increase in milling time led to a lower pHiep, indicative of an increase in SHMP coverage, which was further supported by an intensification in phosphorus content measured by X-ray fluorescence (XRF). Phosphorus content and zeta potential analysis before and after centrifugal washing showed that SHMP was partially removed or hydrolysed for the longer milled pigment samples, whereas no change was observed for shorter milled samples. Relaxation NMR was also performed, where enhanced relaxation rates at longer milling times were associated partially to increases in surface area and exposure of Al sites, as well as physicochemical changes to SHMP density and structure. It is thought that extended milling times may lead to hydrolysis or other structural changes of the dispersant from the high energy milling conditions, allowing easier removal after washing for longer milled pigments.

Influence of pH-Responsive Monomer Content on the Behavior of Di-Block Copolymers in Solution and as Stabilizers of Pickering Latex Particle Emulsifiers.

In this study, diblock copolymers poly(methyl methacrylate)-block-poly (2-dimethylaminoethyl methacrylate) (pMMA-b-pDMAEMA) are investigated for the steric stabilization of latex particles and the subsequent use of these latex particles as Pickering emulsifiers. Solution properties of the diblock copolymers highlight that the pDMAEMA block length influences the critical micelle concentration (CMC) and micelle hydrodynamic diameter in response to changes in pH and the pKa. The block length can also be used as a way to control the particle size of sterically stabilized polystyrene latex particles prepared via emulsion polymerization. The suspension properties of these latex particles are also presented. Emulsion studies using these latex particles as emulsifiers show that both continuous phase pH and electrolyte concentration affect emulsion stability to coalescence. At high pH, stable emulsions are formed due to the affinity of the particles to the interface. At low pH, protonation of the amine groups reduces the affinity and thus droplet coalescence is observed. Increasing the electrolyte concentration improves emulsion stability, but causes an increase in droplet size due to adsorption of flocculated/aggregated particles. Finally, it is shown that these latex particles can be used in conjunction with membrane emulsification techniques to produce emulsions with low polydispersity.

Synthesis and Physical Property Characterisation of Spheroidal and Cuboidal Nuclear Waste Simulant Dispersions.

This study investigated dispersions analogous to highly active nuclear waste, formed from the reprocessing of Spent Nuclear Fuel (SNF). Non-radioactive simulants of spheroidal caesium phosphomolybdate (CPM) and cuboidal zirconium molybdate (ZM-a) were successfully synthesised; confirmed via Scanning Electron Microscopy (SEM), powder X-ray diffraction (PXRD) and Fourier transform infrared (FTIR) spectroscopy. In addition, a supplied ZM (ZM-b) with a rod-like/wheatsheaf morphology was also analysed along with titanium dioxide (TiO2). The simulants underwent thermal gravimetric analysis (TGA) and size analysis, where CPM was found to have a D50 value of 300 nm and a chemical formula of Cs3PMo12O40·13H2O, ZM-a a D50 value of 10 µm and a chemical formula of ZrMo2O7(OH)2·3H2O and ZM-b to have a D50 value of 14 µm and a chemical formula of ZrMo2O7(OH)2·4H2O. The synthesis of CPM was tracked via Ultraviolet-visible (UV-Vis) spectroscopy at both 25 °C and 50 °C, where the reaction was found to be first order with the rate constant highly temperature dependent. The morphology change from spheroidal CPM to cuboidal ZM-a was tracked via SEM, reporting to take 10 days. For the onward processing and immobilisation of these waste dispersions, centrifugal analysis was utilised to understand their settling behaviours, in both aqueous and 2 M nitric acid environments (mimicking current storage conditions). Spheroidal CPM was present in both conditions as agglomerated clusters, with relatively high settling rates. Conversely, the ZM were found to be stable in water, where their settling rate exponents were related to the morphology. In acid, the high effective electrolyte resulted in agglomeration and faster sedimentation.

Imaging in Congenital and Hereditary Abnormalities of the Interventricular Septum: Clinical Anatomy and Diagnostic Clues.

Early identification of congenital heart diseases, specifically those affecting the structural integrity and function of the interventricular septum, in childhood is important toward decreasing the morbidity and mortality of those affected. We review the pertinent clinical and imaging manifestations for those with ventricular septal defects, ventricular septal aneurysms, tetralogy of Fallot, and hypertrophic (obstructive) cardiomyopathy, in addition to discussing first-line imaging studies, including echocardiography, and indications for advanced imaging.

Microarray data and gene expression statistics for Saccharomyces cerevisiae exposed to simulated asbestos mine drainage.

Here we describe microarray expression data (raw and normalized), experimental metadata, and gene-level data with expression statistics from Saccharomyces cerevisiae exposed to simulated asbestos mine drainage from the Vermont Asbestos Group (VAG) Mine on Belvidere Mountain in northern Vermont, USA. For nearly 100 years (between the late 1890s and 1993), chrysotile asbestos fibers were extracted from serpentinized ultramafic rock at the VAG Mine for use in construction and manufacturing industries. Studies have shown that water courses and streambeds nearby have become contaminated with asbestos mine tailings runoff, including elevated levels of magnesium, nickel, chromium, and arsenic, elevated pH, and chrysotile asbestos-laden mine tailings, due to leaching and gradual erosion of massive piles of mine waste covering approximately 9 km2. We exposed yeast to simulated VAG Mine tailings leachate to help gain insight on how eukaryotic cells exposed to VAG Mine drainage may respond in the mine environment. Affymetrix GeneChip® Yeast Genome 2.0 Arrays were utilized to assess gene expression after 24-h exposure to simulated VAG Mine tailings runoff. The chemistry of mine-tailings leachate, mine-tailings leachate plus yeast extract peptone dextrose media, and control yeast extract peptone dextrose media is also reported. To our knowledge this is the first dataset to assess global gene expression patterns in a eukaryotic model system simulating asbestos mine tailings runoff exposure. Raw and normalized gene expression data are accessible through the National Center for Biotechnology Information Gene Expression Omnibus (NCBI GEO) Database Series GSE89875 (https://www.ncbi.nlm.nih.gov/geo/query/acc.cgi?acc=GSE89875).

Coxsackievirus B heart infections and their putative contribution to sudden unexpected death: An 8-year review of patients and victims in the coastal region of Tunisia.

Coxsackieviruses B (CV B) are known as the most common viral cause of human heart infections. Cardiac inflammations contribute to sudden unexpected death (SUD) significantly. The diagnosis remains difficult with the traditional diagnostic tests and must be substantially improved. This has prompted health professionals to seek new diagnostic procedures which may provide important clues regarding underlying etiology. The present study is based on patients with infectious heart diseases and SUD victims with no relevant pathologies. They were investigated for possible CV-B infection. Patients with coronary artery diseases and unnatural road and domestic accident victims served as controls. The samples were studied for CV-B applying PCR. Histopathology for inflammatory markers, immunohistochemistry (IHC) for immune inflammatory cells and the enteroviral VP1-capsid protein were performed. Overall, 102 patients and 87 SUD victims were studied. As controls, 100 patients and 54 SUD unnatural accident victims were enrolled. CV-B were detected in 28 patients and 15 SUD victims. The control group samples were completely virus negative. Compared to controls, IHC revealed a significant presence of T and B lymphocytes within the myocardium. Furthermore, enteroviral VP1-capsid protein were detected from samples by IHC. Applying a comprehensive combination of methods, our results demonstrate the involvement of CV-B in cases of heart infection suggesting they play a significant role in SUD. Our results emphasize the importance of opting for a combination of methods.

Manufacture of poly(methyl methacrylate) microspheres using membrane emulsification.

Accurate control of particle size at relatively narrow polydispersity remains a key challenge in the production of synthetic polymer particles at scale. A cross-flow membrane emulsification (XME) technique was used here in the preparation of poly(methyl methacrylate) microspheres at a 1-10 l h(-1) scale, to demonstrate its application for such a manufacturing challenge. XME technology has previously been shown to provide good control over emulsion droplet sizes with careful choice of the operating conditions. We demonstrate here that, for an appropriate formulation, equivalent control can be gained for a precursor emulsion in a batch suspension polymerization process. We report here the influence of key parameters on the emulsification process; we also demonstrate the close correlation in size between the precursor emulsion and the final polymer particles. Two types of polymer particle were produced in this work: a solid microsphere and an oil-filled matrix microcapsule.This article is part of the themed issue 'Soft interfacial materials: from fundamentals to formulation'.

Measurements of Submicron Particle Adsorption and Particle Film Elasticity at Oil-Water Interfaces.

The influence of particle adsorption on liquid/liquid interfacial tension is not well understood, and much previous research has suggested conflicting behaviors. In this paper we investigate the surface activity and adsorption kinetics of charge stabilized and pH-responsive polymer stabilized colloids at oil/water interfaces using two tensiometry techniques: (i) pendant drop and (ii) microtensiometer. We found, using both techniques, that charge stabilized particles had little or no influence on the (dynamic) interfacial tension, although dense silica particles affected the "apparent" measured tension in the pendent drop, due to gravity driven elongation of the droplet profile. Nevertheless, this apparent change additionally allowed the study of adsorption kinetics, which was related qualitatively between particle systems by estimated diffusion coefficients. Significant and real interfacial tension responses were measured using ∼53 nm core-shell latex particles with a pH-responsive polymer stabilizer of poly(methyl methacrylate)-b-poly(2-(dimethylamino)ethyl methacrylate) (pMMA-b-pDMAEMA) diblock copolymer. At pH 2, where the polymer is strongly charged, behavior was similar to that of the bare charge-stabilized particles, showing little change in the interfacial tension. At pH 10, where the polymer is discharged and poorly soluble in water, a significant decrease in the measured interfacial tension commensurate with strong adsorption at the oil-water interface was seen, which was similar in magnitude to the surface activity of the free polymer. These results were both confirmed through droplet profile and microtensiometry experiments. Dilational elasticity measurements were also performed by oscillation of the droplet; again, changes in interfacial tension with droplet oscillation were only seen with the responsive particles at pH 10. Frequency sweeps were performed to ascertain the dilational elasticity modulus, with measured values being significantly higher than previously reported for nanoparticle and surfactant systems, and similar in magnitude to protein stabilized droplets.